pinuzzo ha detto:
Sarebbe di ottimo aiuto una breve guida per evitare di dover rivivere le peripezie di manuel74.
Ecco quello che ho appuntato, parte in italiano (mie note) e parte in inglese (note varie prese dal sito avsforum):
Firmware update
cavo RS232 dritto
rimappare cavo di conversione USB --> rs232 su COM1/COM2 o COM3
setup a 9600 baud
II) Procedure for Upgrading Main FW on the unit:
Connect the RS232 port of your PC to the receiver (unplugged) RS232 port by using a RS232 straight cable. Keep unit unplugged.
Press ENTER button and in this condition you should plug the receiver in the AC outlet. You will see on the display “Main Update mode”.
After this follow these steps.
a) Open “App_Updater_XXX” folder and Double click on “update.exe”. You will see following GUI.
b) Check the COM port. It should be same as the RS232 port of your PC connected to your receiver (usually COM1).
c) Click on “Main Update” button
DSP update
Per masterizzare il CD con il DSP update :
1. Download imgburn from the website it is free.
2. Install it and run it. Make sure you've unzipped the DSP firmware files you need.
3. In the imgburn menu select "Tools"->"Create CD cue file..."
4. When that interface pops up drag the wav file you extracted for the dsp upgrade into that interface.
5. You don't need to set any other options here. Just press OK and it'll prompt you to where to save the .cue file. If you just press the save button it'll save it to the same place the wav file is located.
6. Once you have the cue file click the "Write image file to disc" button. Or you can select "Mode"->"Write" from the menu.
7. Now in this interface you can browse for the .cue file you made by pressing the browse button (folder icon where it says source) or you can just drag and drop the .cue file you made to the same area to load it.
8. Now just put in a disc and press the write button.
Per effettuare l'update:
connect spidif optical to "Optical 1" port on the BACK of the unit., e map su CD input
select CD input from Onkyo
PS3 audio settings:
BD Settings:
Audio Output (optical digital): bitsream
Music Settings:
Crossfade Playback: off
Audio CD Output Freq: 44.1
Bitmaping: off
Sound Settings:
Audio Output Settings: Linear PCM 2 ch 44.1 kHz and 48kHz checked
1) Switch on the receiver. Wait for 10 seconds. Then press and hold the “DISPLAY” button and while holding it press the “STANDBY/ON” button. This will show in the display the main firmware versions within the unit.
2) Within 3 seconds, press the Tone “ +“ button. Now the display showing the DSP 1 st firmware version, press the “Return” button on the Receiver, then press Play on the CD Player. The Receiver’s display will now say “S/PDIF Update…” for about 15 seconds then “Writing 1 st DSP…” for about 15 seconds, than again S/DIF Update. Now you see “Writing 2 st DSP…” than again S/DIF Update before it changes to “Writing 3 st DSP…” When the writing process has finished the display will say
“Complete!”, then “Clear”, then the Receiver will go to Standby mode. It is possible, that the unit will
not switch OFF automatically, in this case wait for another 10 minutes before switching OFF manually.
3). Now the update is complete! You can check that it has been successful if you read out the FW
version: Switch on the receiver. Wait for 10 seconds. Then press and hold the “DISPLAY” button and while holding it press the “STANDBY/ON” button. The display will show now the Firmware version's.
This will disappear from the display after a few seconds and the Receiver will return to its normal
mode.
se dice di aspettare "S/PDIF Update.." --> Just turn it off, wait for a minute and turn it back on.
