Visualizzazione Stampabile
-
Per la seconda domanda:
Dipende ....
Se il tuo pre in Bypass ti consente di farlo, è indifferente, altrimenti devi farli sull'Oppo.
Occhio che se il pre in bypass multicanale, oltre ai livelli ti fa regolare anche le distanze vuol dire che ridigitalizza e NON è in bypass analogico reale ;)
Il mio AVR, ad esempio, in 5.1 bypass, mi funziona SOLO come Volume generale dell'ampli ! ;)
-
Entro anch'io tra i possessori....grazie a tutti.:)
-
-
Nei thread ufficiali non si fanno confronti con altri prodotti.
-
Mi sono forse espresso male ....
Ma l'Oppo Nu Force e sempre lo stesso apparecchio con base SE e sempre di OPPO 83 stiamo parlando ;)
http://www.nuforce.com/hi/products/o...83se/index.php
E' una versione speciale, come è una versione speciale la SE rispetto all'Oppo Standard ;)
http://www.oppodigital.com/players.asp
-
Ok.
Ma dal momento che esiste una discussione non ufficiale e questa è una variazione del prodotto in oggetto, molto "di nicchia", penso che sarebbe meglio discuterne nell'altro thread.
In ogni caso, accetto anche proposte diverse... ma solo in privato. Grazie.
-
-
Salve a tutti
mio zio mia ha regalato il BPD 83 SE, lo ha acquistato negli USA e naturalmente ha il blocco....... ed allora lui giustamente mi ha anche acquistato il diy multi region code free hardware mod kit, con le istruzioni in inglese. Il problema è non riesco a capirle....
By successfully installing this Kit yourself, it will allow your Oppo BDP-83 to now be REGION-FREE, Code-Free, Multi-Zone, Zone-Free, etc player. This will allow for:
1) Region-Free DVD
2) Remote DVD Region Selection 0-6 / Free
3) Remote Blu-ray Zone selection A, B or C
INSTALLATION INSTRUCTIONS
1. Disconnect the main power cable. Remove the player’s top cover retaining screws, and then lift the rear of the top cover slowly at 45° while carefully pulling it free from the front panel. It is
recommend that you insert a piece of paper or card on each side of the gap between the front panel and the top cover before applying force to tilt and pull the top cover off.
2. Remove the flat ribbon cable running from the front panel to the main board. Gently pull out by hand; the cable is a snug fit.
3. Fold the new cable from the Kit as shown below. Important: The original cable is fitted with the writing facing away from the disc drive. The replacement cable is the other way around. The
important thing is that pin 1 (top) goes to the front of the main board connector (front of player). See >>>
4. Connect the short end of the ribbon cable to front panel.
5. Connect the longer end to the main board. Make sure the cable is flat when pushing it into the sockets and that it is fully inserted. Peal off the backing and attach the board to the disc drive
with the adhesive pad.
6. Connect the power supply cable (red, white, black) to the brown 6-pin plug at the rear of the main board. The plug will only fit in one way – do not force it in it if does not fit.
7. Installation is now complete. Replace the player’s top cover and tighten the screws with the player on a flat surface to ensure the chassis is not twisted.
Region and Zone Code Operation
1. After successful installation of the DIY Kit, your BDP‐83 should be Region‐Free for DVD and Zone A for Blu‐ray by default.
2. If applicable, remember to go to Video Setup > TV System and set the TV system to Multi‐system to enable 60Hz NTSC and 50Hz
PAL output.
3. Region & Zone changes should be made with the player in standby mode.
4. To switch to a different Zone for Blu‐ray, press and hold the blue button on the Remote Control for about 5 seconds until you
hear beeps. Then press 2 for Zone B (you will hear 2 beeps), press 3 for Zone C (you will hear 3 beeps), or to revert to Zone A, press 1
(you will hear 1 beep).
5. To switch to a specific Region for DVD (other than Region‐Free), press and hold the red button on the Remote Control for about 5
seconds until you hear beeps. Then press 2 for Region 2 (you will hear 2 beeps), press 3 for Region 3 (you will hear 3 beeps), etc. To
switch back to Region‐Free, press 0 (you will hear a long beep).
C'è qualcuno che può essermi d'aiuto? Grazie
-
Cos'è che non riesci capire? Ci dovrebbero essere le illustrazioni nel kit, monta il cavo all'interno come è indicato. Poi a lettore in standby premi il pulsante blu sul telecomando fina a quando non senti un bip lungo, quindi premi 1-2-3 a seconda della zona/regione. E' abbastanza semplice.
-
QUOTATURA INUTILE RIMOSSA DA MODERATORE
Grazie per la risposta
Si ci sono le illustrazioni, ma non sono precise...... io devo togliere quello esistente (sopra) e sostituirlo con quello fornito (sotto)? cfr qua sotto
per avere questo risultato?
-
Sì, mi sembra abbastanza semplice ed evidente...
-
Grazie ancora ragazzi per le risposte rapide, mi avete tolto un grosso peso......
-
Citazione:
Originariamente scritto da leenero
Salve a tutti
mio zio mia ha regalato il BPD 83 SE...
lo voglio anch'io uno zio cosiiiiiiii :eek:
ops... fine OT (:( )
-
La nuova beta del firmware OPPO BDP-83 (BDP-83-47-1125B) è ora ufficialmente disponibile. :)
Scaricare il firmware da qui:
http://download.oppodigital.com/BDP8...3-47-1125B.zip
-
Ma c'è solo il link al file? Non c'è anche una pagina con l'elenco di novità/bug-fix e cose del genere?