Ma siete iscritti al forum? 
NEW:
Version 1.6k has been released!
January 27th, 2003: 1.7 Release Candidate
(Jan 26) Version 1.6k Changes:
Added "Chroma Swap" and "Chroma Odd" settings to Setup Menu-> Setup Input. (Also forcefully initializes these settings upon startup)
Note: If you are getting green screens or a photo-negative image, this will likely help you.
(Dec 19) Version 1.6j Changes:
Simplified Input Switch Menu. Everytime you press MENU button (or spacebar on keyboard), the Input Select menu will now be opened by default. Also, the menu is also less cluttered by default too.
Note: Also solves the 3-spacebar-press issue reported by G_ROM
Note2: To make previously selected menu reappear instead, use ENTER key or OK button.
Input Menu is now reconfigurable via the Setup Menu to enable/disable rarely used inputs. By default, Composite-R, Composite-G and Composite-B are now removed from this menu to reduce clutter. To change how you want the Input menu to look, go to Setup Menu -> Setup Input -> Main Inputs. (This is very similiar to configuring the daughterboard)
Daugherboard users now have the option to display all possible daugherboard input combinations, useful for people who use a switcher to allow dual-purpose use of SDI and Composite on the same input. To do so, go to Setup Meni -> Setup Input -> Daughterboard and then select "List All Possible Inputs".
Further tweaks made to LUT. Apparently, my LUT tweaks in 1.6h benefited some users (less stuttering during bright scenes) but some users occasionally experienced 'green noise horizontal lines' every few minutes. This tweak should now eliminate these without degrading the benefits.
DirectX initialization retry extended to 30 seconds.
For users experiencing DirectX initialization issues if HOLO3D used in StartUp
quote:
--------------------------------------------------------------------------------
(Dec 14) Version 1.6h Changes:
Improved Mouse support. You can now click the ends of slider adjustments to go to minimum/maximum settings, or start dragging the slider from the very end of the slider bars successfully. You can also click the OSD graphic to toggle ON/OFF settings or rotate through a list of settings.
If HOLO3D is in the Start Up menu, HOLO3D will now wait longer for DirectX to initialize if DirectX is not fully up and running yet. Apparently, DirectX initialization can be very slow if HOLO3D is run during startup of a Windows XP system since Windows XP is still loading at this time. (This will not slow HOLO3D load time under other normal circumstances)
SDI Initialization Delay adjustment, accessible via Setup Menu. Do not adjust if your SDI is working fine. For those few of you that occasionally get a green screen upon switching to SDI input, you can adjust this to improve SDI input switching reliability.
Fixed very rare LUT adjustment issue where image corruption occured during extreme Brightness/Contrast adjustment settings.
(Dec 6) Version 1.6g Changes:
Even Faster Startup (especially on slower systems)
Better SDI initialization
"Setup Format" has been renamed to "Setup Input"; more intuitive name.
Better initialization of PAL upon startup
(PAL picture stabilizes faster at startup)
Adjustable Input Switch Blanking Delay
(Setup Menu -> Setup Format)
Adjsutable Fast Autoformat Mode - Faster PAL/NTSC detection.
(Setup Menu -> Setup Input -> Autoformat -> Rapid)
Adjustable Size for OSD. Very useful if you have severe overscan or screen masking.
(Setup Menu -> Setup OSD -> OSD Size)
Fully works with 16-bit, 24-bit and 32-bit modes
(Still uses 24-bit Video Overlay. Even works in 256 color mode.)
Two RGB SCART daughterboard modes.
(Rev3/4 users should use RGsB and Rev5 users should use RGBS)
(Nov 29) Version 1.6e Changes:
FAST STARTUP: Much faster, near-instant startup time!
(Originally, whole configuration file was loaded at startup. With daughterboard, the config file more than doubled. I have now changed this to a on-demand cache mechanism. This new cache is the reason of near-instant startup.
DAUGHTERBOARD: Now reselects daughterboard input upon startup.
ORBIT: Orbit now doesn't jump prematurely while adjusting settings such as aspect ratio.
Auto Load Settings has been disabled again, so Version 1.6b resolution-change behaviour is used again now.
Reinitializes video overlay colorkey. May avoid the rare black screen on certain startups.
(Nov 27) Version 1.6c Changes - BETA Maintenance Release:
SECAM support. You will have to turn off AutoFormat (for now) to select SECAM.
SHUTDOWN menu item, via "Setup UI" in Setup Menu
DAUGHTERBOARD support! To select daughterboard configuration, go to Setup Menu -> Setup Format -> Daughterboard. This will add the extra inputs to your main Input select menu.
Confirmation dialog boxes now allows you to press numeric 1 key for equivalent of "YES", and numeric 0 key for equivalent of "NO". This is useful for macros. (Resolution confirm dialog, Shutdown confirm dialog)
More DirectShow is reinitialization everytime input is switched or resolution is switched. This maintains picture settings better and /may/ prevent unexpected picture changes, especially when changing resolutions. You can disable this by turning off Setup Menu -> Setup Format -> Auto Load Settings.
Should now work on Chinese Windows systems
Setup Menu Discrete remote control codes (<INS> or <REC> ) now works on first try immediately after startup. Some users reported that <INS>902 did not work unless entered a second time until the software has been used for a bit. Also inccorect behaviour on second try has been fixed too.
Click here for a list of previous changes in v1.6b
--------------------------------------------------------------------------------
Download NEW v1.6j Update Now!
Note #1: Change of driver policy: If your current drivers work don't upgrade. However, if you get any video problems OR you use a daughterboard, please upgrade to the latest BETA2 drivers dated 11-Nov-2002. Download them here.
Note #2: Install this on top of your existing HOLO3D installation. Don't uninstall first. If you are nervous of losing picture settings, make a backup your HOLO3D.INI file (from where you installed HOLO3D).
Note #3: New users should go to
www.immersiveinc.com/holofiles to download the full install of Version 1.6 first.
__________________
Thanks,
Mark Rejhon
