|
|
Risultati da 1 a 11 di 11
Discussione: RODAGGIO TUBI NUOVI
-
19-04-2008, 13:16 #1
Senior Member
- Data registrazione
- Jan 2008
- Messaggi
- 112
RODAGGIO TUBI NUOVI
Ciao,ho appena comprato un crt barco con i tubi nuovi,mi è stato detto che devo rodaggiarli, tenendo acceso il proiettore per quattro giorni di seguito,seguendo dei precisi parametri datomi da lui,perchè cosi a una migliore messa a fuoco e luminosità,è vero che bisogna fare questo?qualcuno di voi l'ha fatto?
Grazie
-
19-04-2008, 13:28 #2
Advanced Member
- Data registrazione
- Mar 2008
- Località
- Roma
- Messaggi
- 2.009
Ciao, non ho un Barco e non sono un esperto, ma qui ci sono molti membri del forum che hanno dei Barco e sono molto preparati, vedrai che ti sapranno aiutare.
-
20-04-2008, 12:20 #3
Senior Member
- Data registrazione
- Jan 2003
- Località
- toscana italia
- Messaggi
- 639
il mio barco nuovo aveva circa 200 ore di fabbrica
ma non so dire se sia una taratura o un controllo per le morti precoci
-
21-04-2008, 08:57 #4
Senior Member
- Data registrazione
- Jul 2004
- Località
- Lissone(MB)
- Messaggi
- 180
ciao,
i tubi sono nuovi "nuovi" o ricostruiti VDC ?
Nel primo caso non mi pare ,ma non posso confermarlo ,mentre nel secondo SI!
Io per il mio Sony (ma la cosa non cambia ) quando ho messo i tubi ricostruiti VDC l'ho dovuto fare.
RobertoVPR:JVC NZ8+player Oppo 203+processore Lumagen pro
Amplificazione: pre Anthem AVM70+Finali TonewinnerAD7300pa+AD 5100
Diffusori:Infinity Renaissance 90(R+L) 80(c) /Monitor audio/ canton Sub:Audium
Schermo:Screennit 2.35:1 (270x115) Calibrazione:Chromapure
TV:Pana 65HZ1000/JZ48+Pana UB9000/UB450+sinto A/VDenon 1700H DAB+canton serie CD
-
21-04-2008, 09:59 #5
Confermo:
- tubi nuovi di fabbrica: hanno almeno 100 ore di burn-in
- tubi ricostruiti VDC: necessitano di un corretto burn-in pena precoce stampaggio.
Visti i 4gg di fila direi che i tubi sono ricondizionati e quindi è molto importante eseguire la corretta procedura di "rodaggio".
GiancarloFare facilmente ciò che gli altri trovano difficile è talento; fare ciò che è impossibile al talento è genio
Henri Amiel
-
22-04-2008, 11:52 #6
Senior Member
- Data registrazione
- Jan 2008
- Messaggi
- 112
Ho scritto al venditore,e mi ha confermato che si tratta di tubi nuovi ed originali Panasonic al 100%,e che la procedura va fatta sia sui tubi ricostruiti e sia sui nuovi,perche tutti e due hanno bisogno dello stesso rodaggio,e mi ha detto anche,come ha già scritto JAGO,che già quando lo compri nuovo a già su 150-200 ore di uso,perchè vengono rodaggiati i tubi dalla fabbrica,io a questo punto penso che sia vero!
-
22-04-2008, 12:35 #7
Potresti postare la procedura che ti hanno consigliato di seguire?
Grazie.Fare facilmente ciò che gli altri trovano difficile è talento; fare ciò che è impossibile al talento è genio
Henri Amiel
-
23-04-2008, 11:45 #8
Senior Member
- Data registrazione
- Jan 2008
- Messaggi
- 112
Questa è la procedura,è in inglese:
Note: Be aware that this is a slow process and requires 4 days (96 hours) to complete correctly. Shortcuts are not possible here!
1) Set your system up so that a DVD signal is running into the projector with at least a 480p resolution. You don?t want to use 480i, as the scanning lines will be too obvious on the face of the tube, and can wear into the face of the tube during the conditioning process. You want to run at least 480p or line doubling.
2) If you don?t already have this, you?ll need an AVIA test DVD that can display an all white pattern (100IRE) or a PC with an all-white screen test pattern (make sure to turn off your screensaver!).
3) Max out your height and width to 100% or maximum within the menus or controls in your projector. If your raster now spills over the edge of the tube, you?ll be fine, you won?t be driving the tube very hard during the conditioning.
4) Electronically defocus the tube, so that the image on the face of the tube is defocused as much as possible. (this is important, you need to defocus the tube electronically, optical defocusing of the image on the screen will not work for you) Run the focus control of the set to min or max, whatever defocused the tube the most. Put on sunglasses and look directly into the tube to make sure that the image on the face of the tube is now blurry.
5) Select the AVIA disc to produce an all white screen (100IRE) and make sure that the 100 IRE message on the screen is disabled (turn off the subtitles), or you?ll burn a fuzzy ?100 IRE? into the phosphor.
You should now have an all white image displayed on your screen. Freeze frame this screen or use the A-B loop function so that this all white screen remains on the screen. If you have only replaced a tube or two, you can disconnect the applicable R G or B signal to the tubes that you have not replaced, no sense in lighting up the tube face of tubes that work fine.
6) Turn the brightness and contrast down to 30% each. Run the all white field like this for a full 24 hours, then bump up the contrast and brightness by 5% each every 12 hours after that. Keep increasing the brightness and contrast by 5% until you get to 60% brightness and 60% contrast.
7) The Tube Conditioning is now done. Reduce the height and width back to normal, reset the focusing of the set to normal, reconnect any R G or B cables that you took off to disable them, and enjoy your new tube(s). Do a color calibration if required. That?s it!
-
23-04-2008, 12:53 #9
Ottimo grazie.
cmq io sapevo che i tubi comprati nuovi di fabbrica hanno già subuto questo processo, cosa che tra l'altro mi ha anche confermato Curt.
Magari lo ricontatto giusto per averne conferma, dato che sto per cambiare il tubo Blu con uno nuovo di pacca
beh, male che vada avresti solo 96 ore in più sul tubo... che non incidono certo sulla vita complessiva.Fare facilmente ciò che gli altri trovano difficile è talento; fare ciò che è impossibile al talento è genio
Henri Amiel
-
23-04-2008, 17:47 #10
Senior Member
- Data registrazione
- Jan 2008
- Messaggi
- 112
Esatto,come mi ha già detto il venditore, sono rodagiati dalla ditta,ma solo quando compri il proiettore nuovo,quando li devi cambiare te lo devi fare da solo,perchè effettivamente sarebbe strano che quelli della barco ti montano su i tubi apposta per rodaggiarteli e poi li smontano ancora per venderteli,anche perche si tratta di 100 ore,penso che se sarebbe cosi invece di costriuire proiettori starebbero tutto il tempo a rodaggiare tubi!
Visto che il venditore mi ha dato una risposta sensata,penso che sia vero
-
02-05-2008, 18:27 #11
Caspita! Non sapevo di questo rodaggio. Non ne ho mai sentito parlare.
Siccome sono anch'io in procinto di cambiare il mio tubo blu con uno nuovo (non ricostruito, almeno così mi ha assicurato il venditore), queste notizie sono preziose.
Originariamente scritto da gianka
.
Grazie!
Cosimo